DGABK datasheet, DGABK pdf, DGABK data sheet, datasheet, data sheet, pdf, Intersil, Quad SPST, CMOS Analog Switches. DGABK Datasheet, DGABK PDF, DGABK Data sheet, DGABK manual, DGABK pdf, DGABK, datenblatt, Electronics DGABK. DGABK datasheet, DGABK circuit, DGABK data sheet: MAXIM – Quad SPST CMOS Analog Switches,alldatasheet, datasheet, Datasheet search site.
|Published (Last):||4 April 2017|
|PDF File Size:||18.92 Mb|
|ePub File Size:||9.25 Mb|
|Price:||Free* [*Free Regsitration Required]|
Pin Configurations continued To provide protection for overvoltages up to 20V above the supplies, a 1N or 1N type diode should be placed in series with the positive and negative supplies as shown in Figure 2.
Feedthrough via gate capacitance may result in spikes dg201qbk leading and trailing edge of output waveform. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. This dimension allows for off-center lid, meniscus, and glass overrun. B1 maximum dimensions do not include dambar protrusions. An enable input is provided. Parameter guaranteed by design or characterization.
Putere n-am, Tu-mi fii sprijin. In case of conflict between English and Metric dimensions, the inch dimensions control.
Maxim reserves the right to change the datashet and specifications without notice at any time. For more information on TYP values see Note 3. Mold flash or protrusions shall not exceed 0. E and eA are measured with the leads constrained to be perpendicular to datum -C. The DG has a maximum turn-off time of ns and a maximum turn-on time of ns. SR Datasheet – Micropower Direct. All Rights Reserved All other trademarks mentioned are the property of their respective owners.
In either case, source-to-body diodes can be forward biased and conduct current from the signal source. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. Package Information continued The package drawing s in this data sheet may not reflect the most current specifications.
N is the maximum number of terminal positions. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders.
For this configuration dimension b3 replaces dimension b2. Dambar protrusions shall not exceed 0. VO is the steady state output with switch on. Lab 6 in this note.
A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. Typical values are for design aid only, not guaranteed and not subject to production testing. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. Information furnished by Intersil is believed to be accurate and reliable.
For more information on TYP values see Note 2. These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. In the OFF state each channel blocks voltages up to the supply rails. Device mounted with all leads soldered to PC board.
When the enable input is high, a channel is selected by the address inputs, and when low, all channels are off. Copyright Intersil Americas Inc. Dimensions b1 and c1 apply to lead base metal only. Documents Flashcards Grammar checker. Maxim guarantees that these switches will not latch up if the power supplies are disconnected with input signals still connected.
DGABK (MAXIM) – Quad SPST CMOS Analog Switches
These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Measure dimension S1 at all four corners.
Asa cum sunt, la Tine vin! Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product.
DG211 Datasheet PDF
For the latest package outline dg021abk, go to www. For information regarding Intersil Corporation and its products, see www. No circuit patent licenses are implied. The addition of these diodes will reduce the analog signal range to 1V below the positive supply and 1V above the negative supply. Limit diode current to maximum current ratings. D, D1, and E1 dimensions do not include mold flash or protrusions.